Koozali.org: home of the SME Server

Console can't reset to Hostnames+Adresses View

Offline linuxhelp

  • *
  • 173
  • +0/-0
    • Linux PC & Server Support
Console can't reset to Hostnames+Adresses View
« on: November 06, 2008, 11:13:19 PM »
Hello

after a broken SSH Connection to Admin-Console i can not reset to Hostnames+Adresses View

always DNS Forwarding is always shown.

i made an reset and a signal-event post-upgrade but no help...

is there a db-command to set it?

Thanks Tom
Linux PC & Server Support
http://www.linuxonlinehelp.de
.. i Love SME..

Online Stefano

  • *
  • 10,894
  • +3/-0
Re: Console can't reset to Hostnames+Adresses View
« Reply #1 on: November 06, 2008, 11:20:18 PM »
Hi Tom

could you please explain better your problem?

thank you
Ciao
Stefano

Offline linuxhelp

  • *
  • 173
  • +0/-0
    • Linux PC & Server Support
Re: Console can't reset to Hostnames+Adresses View
« Reply #2 on: November 06, 2008, 11:31:01 PM »
Hello

i was using the console to configure the server. Then i get a ssh disconnect, logged in as admin again,
and entered console again, after this i wasn't able to disable dns-forwarding
to solve it i set DNS Server to another Server, and reboot, set it back.
But without entered DNS-Server entry the server-manager shows "DNS Forward" enabled
that i can not enter Local IPs of my other pcs.

I think that Hostnames+Adresses is crumbled.. :-(
i hope that i mst not make a fresh setup again?
it is possible that to instances of console destroys each other?
very bad..
Linux PC & Server Support
http://www.linuxonlinehelp.de
.. i Love SME..

Online Stefano

  • *
  • 10,894
  • +3/-0
Re: Console can't reset to Hostnames+Adresses View
« Reply #3 on: November 06, 2008, 11:36:37 PM »
hi

try this

HTH
Ciao

Stefano

Offline linuxhelp

  • *
  • 173
  • +0/-0
    • Linux PC & Server Support
Re: Console can't reset to Hostnames+Adresses View
« Reply #4 on: November 07, 2008, 10:19:35 AM »
Hello,

no sorry it did not help, i was forced to restore a backup (smeserver.tgz) to get old state.
After this i have made a closer look at /home/e-smith/db/hosts this was the not taken file by the server-manager interface.
For better understanding the work of the pulled databases, if i do a signal-event post-upgrade sme takes the data of the db-files and configure itself? and in which file does sme save ALL generated informations?
i looked at the system with #db configuration show and get:

...
dhcpd=service
    Bootp=deny
    end=192.168.178.250
    start=192.168.178.125
    status=disabled
dnscache=service
    TCPPort=53
    UDPPort=53
    access=private
    status=enabled
dnscache.forwarder=service
    status=enabled
...

it this the area of config for Hostnames and Addresses Settings?
Do sme add the informations into a mysql database?? i found noting there..
« Last Edit: November 07, 2008, 10:21:29 AM by linuxhelp »
Linux PC & Server Support
http://www.linuxonlinehelp.de
.. i Love SME..

Offline janet

  • *****
  • 4,812
  • +0/-0
Re: Console can't reset to Hostnames+Adresses View
« Reply #5 on: November 07, 2008, 11:24:57 AM »
linuxhelp

/home/e-smith/db/databasename

PLEASE read the Dev Guide, the FAQ & useful Howtos that refer to database commands etc.
Please search before asking, an answer may already exist.
The Search & other links to useful information are at top of Forum.