Topic: Could some one help me with the ISDN Connetction?

[Chris]

Hi @all,
I've installed SME V 5.5 on our school server, everthink works, but I couldn't connect to the Internet. In the server is an AVM FritzPCI(2?) Card.
Has someone an idea?

I really not know why I can't connect

Thanks fpr help.

Bye,
   Chris

[guestHH]

Hi,

Did you enter any options in the initial configuration of your server?

Enter the correct options from the table below.

  Type                Required parameters (in addition to type and protocol)

      1   Teles 16.0               irq, mem, io
      2   Teles  8.0               irq, mem
      3   Teles 16.3 (non PnP)     irq, io
      4   Creatix/Teles PnP        irq, io0 (ISAC), io1 (HSCX)
      5   AVM A1 (Fritz)           irq, io
      5   AVM (Fritz!Card Classic) irq, io
      6   ELSA PCC/PCF cards       io or nothing for autodetect (the iobase is
                                   required only if you have more than one ELSA
                                   card in your PC)
      7   ELSA Quickstep 1000      irq, io  (from isapnp setup)
      8   Teles 16.3 PCMCIA        irq, io
      9   ITK ix1-micro Rev.2      irq, io  (from isapnp setup?)
     10   ELSA PCMCIA              irq, io  (set with card manager)
     11   Eicon.Diehl Diva ISA PnP irq, io
     11   Eicon.Diehl Diva PCI     no parameter
     12   ASUS COM ISDNLink        irq, io  (from isapnp setup)
     13   HFC-2BS0 based cards     irq, io
     14   Teles 16.3c PnP          irq, io
     15   Sedlbauer Speed Card     irq, io
     15   Sedlbauer PC/104         irq, io
     15   Sedlbauer Speed PCI      no parameter
     16   USR Sportster internal   irq, io
     17   MIC card                 irq, io
     18   ELSA Quickstep 1000PCI   no parameter
     19   Compaq ISDN S0 ISA card  irq, io0, io1, io (from isapnp setup io=IO2)
     20   NETjet PCI card          no parameter
     21   Teles PCI                no parameter
     22   Sedlbauer Speed Star (PCMCIA) irq, io (set with card manager)
     24   Dr. Neuhaus Niccy PnP    irq, io0, io1 (from isapnp setup)
     24   Dr. Neuhaus Niccy PCI    no parameter
     25   Teles S0Box              irq, io (of the used lpt port)
     26   AVM A1 PCMCIA (Fritz!)   irq, io (set with card manager)
     27   AVM PnP (Fritz!PnP)      irq, io  (from isapnp setup)
     27   AVM PCI (Fritz!PCI)      no parameter
     28   Sedlbauer Speed Fax+     irq, io (from isapnp setup)
     29   Siemens I-Surf 1.0       irq, io, memory (from isapnp setup)
     30   ACER P10                 irq, io (from isapnp setup)
     31   HST Saphir               irq, io
     32   Telekom A4T              none
     33   Scitel Quadro            subcontroller (4*S0, subctrl 1...4)
     34   Gazel ISDN cards (ISA)   irq,io
     34   Gazel ISDN cards (PCI)   none
     35   HFC 2BDS0 PCI            none
     36   W6692 based PCI cards    none
     37   2BDS0 S+, SP/PCMCIA      irq,io (pcmcia must be set with cardmgr)

    Type-Numbers for non-HiSax-drivers:

    101  AVM-B1 PCI               no parameter
    102  AVM-B1 ISA               irq, io

    201  ICN 2B                   io, mem

Regards,
guestHH

[Chris]

I've Set type=27 and protocol=2
thats wrong? ok, I check it with no parameters.
what kind auf protocoll should I use for Germany? I've only found for Europe...any idea?

Thanks.

- Chris

[Dave]

> what kind auf protocoll should I use for Germany? I've only found for#
> Europe...any idea?

Last time I ooked Germany was still in Europe. I don't think its moved.

I think the correct protocol is 2 for "Euro ISDN", though Germany may have some older lines that are DSS1 (I think). You also need to check exactky what AVM card you have. One type 27 needs the IRQ and IO address  to be entered the other doesn't. Check in the logs what error messages you are getting when the system boots up.

Have you tried the "test internet connection" option in the consol setup program? What does that say?

Cheers
Dave.

[Kees Blokland]

..and to add to the confusion:

have a look at your 'messages' file after a reboot, and check that your card is detected and happy:
if in doubt, post the log. you want to see something that looks like this, only much more:

kernel: HiSax: Linux Driver for passive ISDN cards
kernel: HiSax: Version 3.5 (module)
kernel: HiSax: Layer1 Revision 2.41.6.1
kernel: HiSax: Layer2 Revision 2.25
kernel: HiSax: TeiMgr Revision 2.17
kernel: HiSax: Layer3 Revision 2.17.6.1
kernel: HiSax: LinkLayer Revision 2.51
etc etc..

kees