Koozali.org: home of the SME Server

Legacy Forums => Experienced User Forum => Topic started by: Alex on October 24, 2002, 07:24:05 PM

Title: From softwareMirroring to single install
Post by: Alex on October 24, 2002, 07:24:05 PM: Hi
I have just a software mirror sme5.5 and i want to switch to a single install

Have i to do a fresh install, or can i do an upgrade?

Or is it possible to take one hdd out of the system without loosing data?

Did anyone tested this?

Thanks
Alex
Title: Re: From softwareMirroring to single install
Post by: Nathan Fowler on October 24, 2002, 09:57:23 PM: Just take one of the HDD's out of the system, it'll act as a broken RAID-1 array and you won't lose data (Isn't that the point of RAID-1 after all? If one drive fails the other continues to operate).

Hope this helped,
Nathan
Title: Re: From softwareMirroring to single install
Post by: Alex on October 24, 2002, 10:47:54 PM: Thank you!

Just one more question:

Is the system so fast as a single install, after taking off a hdd ? Thats the reason, why i want to go back to single drive!
Title: Re: From softwareMirroring to single install
Post by: Nathan Fowler on October 24, 2002, 10:53:01 PM: No, you won't notice any increase in speed. The CPU overhead for RAID-1 calculations aren't very high at all, and unless you have both disks on the same IDE channel you won't notice a speed increase in drive throughput.

Hope this helped,
Nathan
Title: Re: From softwareMirroring to single install
Post by: Alex on October 24, 2002, 10:59:01 PM: I tried the mirroring just one day! And while copying files to sme I was not able to listen to mp3 wich are saved on sme, and the switch doesnt showed me a lot of traffic, only hdd' LED on sme is all teh time on.

The Hdd are not on the same ide channel.
Title: Re: From softwareMirroring to single install
Post by: Alex on October 24, 2002, 11:07:48 PM: Ok i have now an single drive install again
and it is much faster than as mirrored!

Thank you for your help!

AleX
Title: Re: From softwareMirroring to single install
Post by: Nathan Fowler on October 24, 2002, 11:16:24 PM: Wow, you must have a slow box. I've got two 5400 RPM 1.2GB Quantum drives in a P2-300Mhz and I have very little CPU over-head and very little Disk I/O and bottle-necks.

I'm also doing almost constant Disk I/O on that box due to the webserver, mail server, and cron jobs.

Glad it's working fast for you.

Nathan
Title: Re: From softwareMirroring to single install
Post by: Alex on October 25, 2002, 01:48:09 AM: That box isnt so slow :
AMD XP1800
512MB RAM
7200 rpm 120GB IBM
But in mirror mode it was so slow, i was wondering my self

ALeX
Title: Re: From softwareMirroring to single install
Post by: Michael Smith on October 25, 2002, 02:12:41 AM: If you only tried the mirroring for one day, it probably never finished the software mirror, so the machine was busy. I bet if you'd waited a day or so the system would've returned to a higher performance level. As pointed out earlier, you DID have the drives as masters on separate IDE channels, correct?
Title: Re: From softwareMirroring to single install
Post by: Alex on October 25, 2002, 02:39:43 AM: Yes every hdd was a master hdd on seperate channel and no other devices on each ide-channel.

But if i didn't copied something hdd led was off, so the mirroring must be finished.

Alex
Title: Re: From softwareMirroring to single install
Post by: Nathan Fowler on October 25, 2002, 04:48:12 AM: You can always check on the status of your RAID array by viewing the contents of /proc/mdstat:

cat /proc/mdstat

[UU] means the partitions are uniform.
Title: Re: From softwareMirroring to single install
Post by: Alex on October 25, 2002, 05:13:25 AM: Thank you for your help! I will try it, when i will have an test server again!

AleX
Title: Re: From softwareMirroring to single install
Post by: Lowell on October 27, 2002, 06:25:43 PM: Looking at Michael Smith's response, If I don't have any thing else on a cable, where would I put the CD rom?
My mirror ends up showing my 15 gig drives as 6.3 gig.