Koozali.org: home of the SME Server

Legacy Forums => General Discussion (Legacy) => Topic started by: Stuart on July 09, 2001, 03:22:51 PM

Title: Dialing in to e-smith
Post by: Stuart on July 09, 2001, 03:22:51 PM

I am getting ADSL on and would like to dial into e-smith from outside . What would be best to use........Thanks Stuart

Title: Re: Dialing in to e-smith
Post by: Michael Maxwell on July 09, 2001, 10:47:40 PM

Hi Stuart,

Have a look at http://home.iprimus.com.au/michaelmaxwell/ - [Mgetty under e-smith] This will give you some idea on the subject.

--
Michael

Stuart wrote:
>
> I am getting ADSL on and would like to dial into e-smith from
> outside . What would be best to use........Thanks Stuart

Title: Re: Dialing in to e-smith
Post by: rod on July 10, 2001, 10:35:11 AM

Have a look at the uers 'howto's there is an add on package for e-smith that has been recently updated to support e-smith 4.1.2 dial in.
I am currently using it on an ADSL connected e-smith box for exactly what you are proposing.
Regards

Title: Re: Dialing in to e-smith
Post by: Peter on July 11, 2001, 12:31:36 AM

Rob can't find the update for e-smith 4.1.2 dial in can you direct me

Thanks

Title: Re: Dialing in to e-smith
Post by: rod on July 11, 2001, 09:56:13 AM

The how to is here ftp://ftp.e-smith.org/pub/e-smith/contrib/StephenNoble/RPMS/noarch/readme-dialin-server.html
The rpms are here
ftp://ftp.e-smith.org/pub/e-smith/contrib/StephenNoble/RPMS/noarch/

regds
Rod

Title: Re: Dialing in to e-smith
Post by: Stuart on July 11, 2001, 02:12:52 PM

Thanks for your reply Rod. This is what i wanted and i may have time this weekend to have a look at it. I thank you peter for asking the question i was going to ask.I had not found the information either. Which package did you install Rod?

Title: Re: Dialing in to e-smith
Post by: rod on July 11, 2001, 06:04:12 PM

Depends upon which version of e-smith you are running. The HowTo details which version to use depending upon the version of e-smith.

Title: Re: Dialing in to e-smith
Post by: Peter on July 11, 2001, 11:22:54 PM

Many thanks Rod I will have a look at it ASAP

Peter

Title: Re: Dialing in to e-smith
Post by: Stuart on July 12, 2001, 01:50:32 PM

I will be using 4.1.2 however i am inexperenced in linux. there is a lot to learn

Title: Re: Dialing in to e-smith
Post by: Sidney on July 12, 2001, 06:37:24 PM

Greetings,
 
  I am also tring to get this to work. Last night I down loaded
mgetty 1.1.25-5.i386. Tryed to follow the instruction on this web site http://home.iprimus.com.au/michaelmaxwell/Mgettyundere-smith.html
but not much success. when I try to install mgetty with this command "rpm -Uhv mgetty-x.i386.rpm --nodeps" I get no such file exists. so I type this command "rpm -i mgetty-x.i386.rpm" it installs. I used Mc to edit the login.config file I added this line
"/AutoPPP/ - - /usr/sbin/pppd auth -chap +pap login debug lock"

then I edit the dialin.config to add the phone numbers extension that I would allow to connect "459, 245, 426"
I wasn't to sure if I was doing this part right.

I then wanted to test the modem witch is a external 56k us robotics modem I think it is connected on com 2 but I am not sure. when I type
"/sbin/mgetty ttyS0" to check com 1 and It just hangs there for a minute and nothing happens just goes back to the prompt#.
I type this command "/sbin/mgetty ttyS1" to check com 2
and it just blinks and goes back to the prompt#

I tryed to dail the number but the modem doesn't anwser.
Any other sugestion ?

Any help would be much Appreciated.


Thanks

Title: Re: Dialing in to e-smith
Post by: Peter on July 14, 2001, 03:01:03 AM

Rod
Many thanks I now have the dialin working

These are the links Rod gave
 
The how to is here ftp://ftp.e-smith.org/pub/e-smith/contrib/StephenNoble/RPMS/noarch/readme-dialin-server.html
The rpms are here
ftp://ftp.e-smith.org/pub/e-smith/contrib/StephenNoble/RPMS/noarch/

Peter