Koozali.org: home of the SME Server
Legacy Forums => Experienced User Forum => Topic started by: Gizmor on February 13, 2004, 06:24:27 AM
-
Hi,
I have since 02-02-04 ADSL with that ADSL came the Speedtouch modem installed it works ok connection good then i tryed to install the e-smith 6.0 system that didn't work i set the server mode to server only because the server only have to act as mail/web server
but if i go to the internal then i dont get met xoops website (primary website)that i had but very slow only the text, from my other site (ibay)is see the website but this one is HTML only then i thougt that the php/mysql service was not running ore something then i looked further and i opened the mydms url from my server en i see mydms running fine so mysql/pph services are running, the immages from my primary site aren't loaded so i uploaded the files again mabe there corrupted i thougt but i didn't make a difference. what can be the problem ?
plz help me getting crazy :cry:
-
Sorry for my english i'm dutch and my english is not very well. :-(
/second post
i had to becease i'm a guest i can;t edit the my last post.
-
Pls specify if Speedtouch USB or Ethernet ?
About Pictures, did you reset your browser cache ?
Kan ook in het nederlands, ik snap niet direkt wat je probleem is.
-Hervé
-
Blij dat het in het nederlands kan :-D
ik heb een ethernet modem 510 van (speedtouch)
het probleem is dat ik dus ik mn e-smith niet meer als gateway wil gebruiken omdat dat al in de ADSL modem zit, dus heb ik de server ingesteld op server-only maar ik krijg het niet werkend intern kan die in een geen plaatjes meer laden heb ze ook al weer een x geupload en hij kan op de een of andere manier geen gebruik maken van mysql/php (intern) en dan nog het volgende de e-smith pc in al helemaal niet meer te bereiken vanaf buiten (extern) ondanks de port forwarding.
Dus ik wil dus mn e-smith NIET als gateway, ik heb de DHCP Server uitgezet en heb een inet connectie op de e-mith computer die werkt alleen het bovenstaande niet.
-
Now I understand the question(s) :-)
( Will reply in english in such a way that other peoples can follow issue. If you have problem, I can translate it later ).
You are using a modem/nat router to connect your sme to the internet, and SME runs in ' server-only ' mode.
It should be OK ...
Would suggest to check the following :
1) Did you put the 'intranet' on the right NIC (suppose there are two nics in the SME, since it was Gateway)
2) Are you sure all IP's are compatible, that you do not have conflits from IP's coming from the router (dhcp from speedtouch ? ). Server must have fixed ip within your intranet range.
3)Portforward on your router (speedtouch) should work.
I guess you are only forwarding port80 to your SME.
4) Take a look to your cabling/hubs/switches/Nic's. Cabling or bad hub/switch port or bad NIC is from time to time the cause of such problems. Also try without the 'speedtouch' connected to the network ( for example ).
Hope this can help.
- Hervé
-
Now I understand the question(s) :-)
( Will reply in english in such a way that other peoples can follow issue. If you have problem, I can translate it later ).
You are using a modem/nat router to connect your sme to the internet, and SME runs in ' server-only ' mode.
It should be OK ...
Would suggest to check the following :
1) Did you put the 'intranet' on the right NIC (suppose there are two nics in the SME, since it was Gateway)
2) Are you sure all IP's are compatible, that you do not have conflits from IP's coming from the router (dhcp from speedtouch ? ). Server must have fixed ip within your intranet range.
3)Portforward on your router (speedtouch) should work.
I guess you are only forwarding port80 to your SME.
4) Take a look to your cabling/hubs/switches/Nic's. Cabling or bad hub/switch port or bad NIC is from time to time the cause of such problems. Also try without the 'speedtouch' connected to the network ( for example ).
Hope this can help.
- Hervé
Thanks for your reply
1) i have put the intranet on the right nick getting a inet connection on the e-smith is not a problem.
I can go to my server from the local network.
2)Yes i gave my E-smith IP 10.0.0.152 and for as i can see there are no conflicts with it. How can i check that ?
3)I have forwarded port 80 on my speedtouch to 10.0.0.152 (IP from the server) But it doesn't work :S
4)The cables/hub is working fine i didn't change the cables of nic on the server and they worked ok for about 1 a 2 years that the server has functioning as gateway.
-
2)Class A Network ( 10.0.0.152/8 ) ...
-Do you use DHCP from Speedtouch ?
If yes, which range
-What are the Netmasks in SME/Client PC's/Speedtouch ?
Your pb can also be introduced using mixed or incompatible netmask.
-Hervé
-
2)Class A Network ( 10.0.0.152/8 ) ...
-Do you use DHCP from Speedtouch ?
If yes, which range
-What are the Netmasks in SME/Client PC's/Speedtouch ?
Your pb can also be introduced using mixed or incompatible netmask.
-Hervé
Yes i use DHCP from the Speedtouch range from 10.0.0.150 to 10.0.0.200 with subnetmask 255.255.255.0 (for as far as i know)
(sme is set to netmask 255.255.255.0 and the other windows systems to)
What is "class a network"?
and what means that /8 or /32 i got /32 behind my outside ip.
Sorry don't know what you mean by PB :-(
-
Gizmor,
Try this:
http://members.home.nl/timothee/mxstreamlinux.pdf
It will work perfectly with all SME versions.
-
Gizmor,
Try this:
http://members.home.nl/timothee/mxstreamlinux.pdf
It will work perfectly with all SME versions.
If i do this thingfs with my modem can i change it back if i want ? and what about the warranty ?
-
ive read how to hack my speedtouch modem but (sorry i'm liitle carefully with this) they only tested it on ISDN modem of alcatel and they name firmware "GSV7AA3.261" while i'm having "LLT6AA4.230" so if i would do this can i go bakc make it undone.
don't feel much to send to a ADSL modem repair center :-(
-
Gizmor,
Try this:
http://members.home.nl/timothee/mxstreamlinux.pdf
It will work perfectly with all SME versions.
HF, is this doc to be found in english?
-
so no one knows if i can use this modem hack tutorial ? i realy want to know if somebody did it once on an standard ethernet modem (ADSL)
-
Gizmor,
I cannot read the document 'entirely' because it is not english. But, i believe all it is having you do is access the modem by way of a browser interface and adjust the modem settings directly. If you are worried about this causing problems with the modem this is done on ALL DSL modems that require any adjustments appropriate for the setup of users. They usually hae a 'reset' button on them so you can always return to the defult settings. It does not hurt the modem. Now, if there is more to this document than adjusting modem settings, I am unable to see it. I wish I could find this doc in english.
Craig Jensen
-
cjensen,
This document is about a modem hack so its not only settings. Setting can be set to default but a hack is something different.
-
The Speed Touch modems I've worked with come with a built in Firewall. That explains why you can see your web from inside but not from outside. You need to punch holes in the modem to allow services in, such as port 80 traffic. The alternative to punching holes in the modem is to completely remove the firewall and let E-Smith be your firewall. There is an option to set the output of the modem in the DMZ zone. If you do that all the ports you have open on E-Smith will be open to the world. Since E-Smith comes with a really good firewall you shouldn't even need the Speed Touch firewall.
-
:lol:
Okay i see what you did. Had the same problem. Have a Speedtouch 510 with SME server 6.0. What i also did is that i put the SME server on the DMZ of the Speedtouch now it works like a charm. Only have to fix email,vpn and Mysql. :cry:
Just a noob on linux so it could take a while. Have one question do. If i want to connect 2 SME servers on a Speedtouch 510 with vpn is that possible? Servers are on different locations and is a test for my company to supply a vpn administration solutions for our clients. Enne als het in nederlands kan mag dat ook. :hammer:
-
:lol:
Okay i see what you did. Had the same problem. Have a Speedtouch 510 with SME server 6.0. What i also did is that i put the SME server on the DMZ of the Speedtouch now it works like a charm. Only have to fix email,vpn and Mysql. :cry:
Just a noob on linux so it could take a while. Have one question do. If i want to connect 2 SME servers on a Speedtouch 510 with vpn is that possible? Servers are on different locations and is a test for my company to supply a vpn administration solutions for our clients. Enne als het in nederlands kan mag dat ook. :hammer:
Ik heb mn server ook in DMZ staan maar toch werkt het niet en 2 vpn's zoals jij dat wilt gaat denk ik niet :-(
-
Hi Gizmor,
Je moet wel apart ff de normale poorten forwarden naar je server. Alle andere niet normale poorten worden al afgeleverd op je server.
Zal proberen om een screenshot te maken van de conf in de router.
-
8-) Okay stupid me i need to login first before i give a reply. Gizmor that reply was from me so sorry if it says guest. :-?
-
:-o
Can it even get better yes it can. Okay what i did is the following. Have a 510 alcatel ethernet router. I have 2 sme servers on my intranet. 1 as server/gateway and one as server. What i did is that i have disabled all firewall capabilaties on the 510 and have all ports forwarded to my sme gateway. That worked okay and i could do everything. Now i have restored the capabilaties of the 510 and i put up a server only sme. Forwarded mail, vpn and http to it and that works also great. What you have to keep in mind is that SME has two functions as Server only:
1. Fileserver
2. Authentication server.
Other server is still runnning in network and that is my test server.
Confused?? You bet but is works. :lol:
-
Owke dat uitzetten van de firewall had ik ook al gedaan maar klotp eht dat die speedtouch mn server ook niet ziet ?
want als ik de Speedtouch inga zie ik mijn pc staan met het IP adres erachter wat de speedtouch heeft gegeven maar de server zie ik nooit staan is dat nu goed of slecht ?
In server-only mode sme has more then 2 functions
- webserver
- fileserver
- mailserver
- auth. server
so sme wont fill the job as a gateway but only as a stand alone server
-
Nee dat klopt niet. Als het goed is moet je pc en je server zichtbaar zijn in je Speedtouch. Server heeft een vast ip nummer dat in dezelfde range valt die de speedtouch uitdeelt. Let er wel op Default server in je speedtouch is het ipnummer van je server. Je server moet jezelf in de dns van je speedtouch toevoegen en daarna kan je poorten forwarden naar je server.
I know SME has more functions as Server only. Only in my setup it has only two.
-
Nee dat klopt niet. Als het goed is moet je pc en je server zichtbaar zijn in je Speedtouch. Server heeft een vast ip nummer dat in dezelfde range valt die de speedtouch uitdeelt. Let er wel op Default server in je speedtouch is het ipnummer van je server. Je server moet jezelf in de dns van je speedtouch toevoegen en daarna kan je poorten forwarden naar je server.
I know SME has more functions as Server only. Only in my setup it has only two.
Ik had hem al toegevoegd voor dat je had gereageerd zitten we toch een beetje op dezelfde hoogte maar helaas werkt het nog steeds niet :-(