Koozali.org: home of the SME Server

Legacy Forums => General Discussion (Legacy) => Topic started by: MetalMick on October 09, 2001, 07:14:24 PM

Title: Quake and e-smith
Post by: MetalMick on October 09, 2001, 07:14:24 PM

Hi,

Im running e-smith 4.1.1 and have setup a wired and wireless lan using e-smith as a router between the wireless and wired networks.

wireless lan (eth1) >>> E-smith << Wired lan (eth0)
                                     ^^^
                         56k modem (ppp0)

Im trying to run Quake bettween the two networks.. Quake runs fine between boxes on the wireless and wired networks but e-smith will not route packets from and to the wireless and wired networks.

Any help would be great :D

Thanx, Mick

Title: Re: Quake and e-smith
Post by: MetalMick on October 09, 2001, 07:21:02 PM

MetalMick wrote:

> Im trying to run Quake bettween the two networks.. Quake runs
> fine between boxes on the wireless and wired networks but
> e-smith will not route packets from and to the wireless and
> wired networks.


Quake runs fine between wireless boxes and wired boxes but will "not" route between the two networks. :D

Title: Re: Quake and e-smith
Post by: enigma01 on October 10, 2001, 01:10:40 AM

Hi MetalMick

you need to install the portforwarding rpm from the contributed rpms and set the ports up to the required machine.

BEst of luck

enigma

Title: Re: Quake and e-smith
Post by: MetalMick on October 10, 2001, 04:48:25 PM

Hi Enigma,

Thanx for the reply

I can't using use the portforwarding rpm because i have 3 boxes on the wireless network and 2 boxes on the wired network that i wish to connected together.

If i use portforwarding this will only work between say one wireless box to a wired box. I want to setup all 5 boxes.

Setting up IP Masquerade to allow port 26000 is what i need to setup.

I tryed loging into a Quake server via the net with no luck.

[root@ns /root]# lsmod
Module                  Size  Used by
ray_cs                 18560   1
ds                      6288   1  [ray_cs]
i82365                 21680   1
pcmcia_core            44160   0  [ray_cs ds i82365]
ip_masq_vdolive         1408   0  (unused)
ip_masq_raudio          2976   0  (unused)
ip_masq_quake           1392   0  (unused)
ip_masq_irc             1632   0  (unused)
ip_masq_icq            10144   0  (unused)
ip_masq_h323            3600   0  (unused)
ip_masq_ftp             4192   0  (unused)
ip_masq_cuseeme         1120   0  (unused)
slip                    7904   2  (autoclean)
ppp-4mppe              21552   2  (autoclean)
slhc                    4576   2  (autoclean) [slip ppp-4mppe]
3c59x                  19440   1  (autoclean)

Note that "ip_masq_quake" is loaded.....

any idea's ???

MetalMick

enigma01 wrote:
>
> Hi MetalMick
>
> you need to install the portforwarding rpm from the
> contributed rpms and set the ports up to the required machine.
>
> BEst of luck
>
> enigma

Title: Re: Quake and e-smith
Post by: gpitch@hotmail.com on October 10, 2001, 06:14:42 PM

I have a couple:

1     If security is not a concern setup e-smith as server only, this way all traffic comes in and out of your LAN, downside is there is no firewall!

2     Run a dedicated quake server behind the e-smith, and connect to this (port fprwarding to main Q-server



after that - its beyond my expereince to offer any advice

Hope this is of some small help

Gavin