Koozali.org: home of the SME Server

Obsolete Releases => SME VoIP (Asterisk, SAIL etc) => Topic started by: jvels on December 28, 2006, 08:52:27 PM

Title: Selintra Sail PCI card
Post by: jvels on December 28, 2006, 08:52:27 PM

Hi

When I try search for my PCI card i got:

Code: [Select]



PCI Telephony Cards

There are currently no PCI Telephony cards registered on the system


I read: http://81.149.154.14/docs/cgi-bin/view/Main/DocChapter258

And get the values:

Code: [Select]


00:09.0 Communication controller: Motorola Wildcard X100P
        Subsystem: Motorola: Unknown device 0000
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (250ns min, 32000ns max)
        Interrupt: pin A routed to IRQ 169
        Region 0: I/O ports at b800 [size=256]
        Region 1: Memory at febfe000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=55mA PME(D0+,D1-,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-





00:09.0 Class 0780: 1057:5608
        Subsystem: 1057:0000
        Flags: bus master, medium devsel, latency 32, IRQ 169
        I/O ports at b800 [size=256]
        Memory at febfe000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [40] Power Management version 2


Run:

Code: [Select]


db selintra-work set pci:1057:5608:1057:0000 sysdev probe wctdm zzeor EOR


Go to the server panel and comit... try again to search but no card :(

Some ideas? I should be a Digium clone X100P card...

Title: Selintra Sail PCI card
Post by: jvels on December 28, 2006, 09:45:00 PM

I try this:

Code: [Select]


[root@velsserver ast]# modprobe wcfxo
WARNING: /etc/modprobe.conf line 50: ignoring bad line starting with 'post-install'
WARNING: /etc/modprobe.conf line 51: ignoring bad line starting with 'post-install'
WARNING: /etc/modprobe.conf line 52: ignoring bad line starting with 'post-install'
WARNING: /etc/modprobe.conf line 53: ignoring bad line starting with 'post-install'
WARNING: /etc/modprobe.conf line 54: ignoring bad line starting with 'post-install'
WARNING: /etc/modprobe.conf line 55: ignoring bad line starting with 'post-install'
WARNING: /etc/modprobe.conf line 56: ignoring bad line starting with 'post-install'
WARNING: /etc/modprobe.conf line 57: ignoring bad line starting with 'post-install'
WARNING: /etc/modprobe.conf line 58: ignoring bad line starting with 'post-install'
WARNING: /etc/modprobe.conf line 59: ignoring bad line starting with 'post-install'
WARNING: /etc/modprobe.conf line 60: ignoring bad line starting with 'post-install'
WARNING: /etc/modprobe.conf line 61: ignoring bad line starting with 'post-install'
WARNING: /etc/modprobe.conf line 62: ignoring bad line starting with 'post-install'
WARNING: /etc/modprobe.conf line 63: ignoring bad line starting with 'post-install'
FATAL: Module wcfxo not found.



My card use this driver I think:
 Digium X100P/X101P FXO     wcfxo

Code: [Select]


db selintra-work set pci:1057:5608:1057:0000 sysdev probe wcfxo zzeor EOR


I have tryed with the command but no result :(

Title: Selintra Sail PCI card
Post by: SARK devs on December 28, 2006, 11:36:12 PM

Hi,

Looking at your post I would guess that you have upgraded your system either with yum update or you are inadvertently running the smp version of the kernel.  Either can cause the problems you are seeing.

Do...

uname -r

at the console.  

All of the Selintra asterisk rpms are compiled against the vanilla 7.0 34-EL and 34-ELsmp kernel.  There is a section in the docs covering this here...

http://81.149.154.14/docs/cgi-bin/view/Main/DocChapter2510

I think this will probably be your problem.

Kind Regards

Selintra

Title: Selintra Sail PCI card
Post by: jvels on December 29, 2006, 08:38:48 AM

Hi

Code: [Select]


[root@velsserver ~]# uname -r
2.6.9-34.ELsmp



I have made the install on a fresh install SME

Best Regrads
Jesper Vels

Title: Selintra Sail PCI card
Post by: jvels on December 29, 2006, 11:09:01 AM

I have tryed to reboot my server, and choose the second of the option... and now my card is discovered   :D

But why because I have choose the second option now:

Code: [Select]


[root@velsserver ~]# uname -r
2.6.9-34.EL