Koozali.org: home of the SME Server
Other Languages => Italiano => Topic started by: filloweb on November 16, 2007, 12:41:35 PM
-
Ciao.
Ho un Fujitsu-Primergy Econel 200 con 1GB di RAM e due dischi SATA.
Durante l'installazione il server si blocca durante l'installazione del pacchetto "udev-039-10.15.EL4-i386".
Ho anche provato ad installare
CentOS 4.5
RHEL 4 Update 5
ma fa uguale.
Il server quando si blocca non switcha sulle altre console ( F2, F3, F4, F5, F6 ).
Ho dovuto installarlo svariate volte per avere l'output di tutte le console:
http://www.i80.it/Temp/SME/Console.jpg
http://www.i80.it/Temp/SME/ALT+F2.jpg
http://www.i80.it/Temp/SME/ALT+F3.jpg
http://www.i80.it/Temp/SME/ALT+F4.jpg
http://www.i80.it/Temp/SME/ALT+F5.jpg
http://www.i80.it/Temp/SME/ALT+F6.jpg
Le schermate, pero' sono riferite alla fase di creazione e formattazione del sistema, perche' durante la fase di installazione dei pacchetti NON esce alcun nuovo messaggio.
Ho anche provato su disco IDE, disco USB, a disabilitare da BIOS: ACPI, APM e HyperTrading ma non cambia nulla.
Con Ubuntu 6.06 LTS e 7.04 va tutto a buon fine e funziona egregiamente.
L'output di "lspci -v" e' questo:
00:00.0 Host bridge: Intel Corporation E7320 Memory Controller Hub (rev 0c)
Subsystem: Fujitsu Siemens Computer GmbH Unknown device 1073
Flags: bus master, fast devsel, latency 0
Capabilities: [40] Vendor Specific Information
00:00.1 Class ff00: Intel Corporation E7320 Error Reporting Registers (rev 0c)
Subsystem: Fujitsu Siemens Computer GmbH Unknown device 1073
Flags: fast devsel
00:02.0 PCI bridge: Intel Corporation E7525/E7520/E7320 PCI Express Port A (rev 0c) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000a000-0000afff
Capabilities: [50] Power Management version 2
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit- Queue=0/1 Enable-
Capabilities: [64] Express Root Port (Slot-) IRQ 0
00:03.0 PCI bridge: Intel Corporation E7525/E7520/E7320 PCI Express Port A1 (rev 0c) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Capabilities: [50] Power Management version 2
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit- Queue=0/1 Enable-
Capabilities: [64] Express Root Port (Slot-) IRQ 0
00:1c.0 PCI bridge: Intel Corporation 6300ESB 64-bit PCI-X Bridge (rev 02) (prog-if 00 [Normal decode])
Flags: bus master, 66MHz, fast devsel, latency 64
Bus: primary=00, secondary=03, subordinate=03, sec-latency=64
I/O behind bridge: 0000c000-0000cfff
Capabilities: [50] PCI-X bridge device
00:1d.0 USB Controller: Intel Corporation 6300ESB USB Universal Host Controller (rev 02) (prog-if 00 [UHCI])
Subsystem: Fujitsu Siemens Computer GmbH Unknown device 1073
Flags: bus master, medium devsel, latency 0, IRQ 16
I/O ports at 9880 [size=32]
00:1d.1 USB Controller: Intel Corporation 6300ESB USB Universal Host Controller (rev 02) (prog-if 00 [UHCI])
Subsystem: Fujitsu Siemens Computer GmbH Unknown device 1073
Flags: bus master, medium devsel, latency 0, IRQ 19
I/O ports at 9c00 [size=32]
00:1d.4 System peripheral: Intel Corporation 6300ESB Watchdog Timer (rev 02)
Subsystem: Fujitsu Siemens Computer GmbH Unknown device 1073
Flags: medium devsel
Memory at f9fff800 (32-bit, non-prefetchable) [size=16]
00:1d.5 PIC: Intel Corporation 6300ESB I/O Advanced Programmable Interrupt Controller (rev 02) (prog-if 20 [IO(X)-APIC])
Subsystem: Fujitsu Siemens Computer GmbH Unknown device 1073
Flags: bus master, fast devsel, latency 0
Capabilities: [50] PCI-X non-bridge device
00:1d.7 USB Controller: Intel Corporation 6300ESB USB2 Enhanced Host Controller (rev 02) (prog-if 20 [EHCI])
Subsystem: Fujitsu Siemens Computer GmbH Unknown device 1073
Flags: bus master, medium devsel, latency 0, IRQ 21
Memory at f9fffc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Capabilities: [58] Debug port
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 0a) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
I/O behind bridge: 0000d000-0000efff
Memory behind bridge: fa000000-fbffffff
Prefetchable memory behind bridge: 50000000-500fffff
00:1f.0 ISA bridge: Intel Corporation 6300ESB LPC Interface Controller (rev 02)
Flags: bus master, medium devsel, latency 0
00:1f.2 IDE interface: Intel Corporation 6300ESB SATA Storage Controller (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Fujitsu Siemens Computer GmbH Unknown device 1073
Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 18
I/O ports at 01f0 [size=8]
I/O ports at 03f4 [size=1]
I/O ports at 0170 [size=8]
I/O ports at 0374 [size=1]
I/O ports at fc00 [size=16]
00:1f.3 SMBus: Intel Corporation 6300ESB SMBus Controller (rev 02)
Subsystem: Fujitsu Siemens Computer GmbH Unknown device 1073
Flags: medium devsel, IRQ 11
I/O ports at 0400 [size=32]
04:01.0 SCSI storage controller: Adaptec AHA-2940U/UW/D / AIC-7881U (rev 01)
Subsystem: Adaptec AHA-2940UW SCSI Host Adapter
Flags: bus master, medium devsel, latency 64, IRQ 17
I/O ports at e800 [disabled] [size=256]
Memory at fbfff000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at 50020000 [disabled] [size=64K]
Capabilities: [dc] Power Management version 1
04:02.0 RAID bus controller: Promise Technology, Inc. PDC20319 (FastTrak S150 TX4) (rev 02)
Subsystem: Promise Technology, Inc. PDC20319 (FastTrak S150 TX4)
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 20
I/O ports at ec00 [size=64]
I/O ports at e480 [size=16]
I/O ports at e400 [size=128]
Memory at fbffe000 (32-bit, non-prefetchable) [size=4K]
Memory at fbfc0000 (32-bit, non-prefetchable) [size=128K]
Expansion ROM at 50030000 [disabled] [size=64K]
Capabilities: [60] Power Management version 2
04:03.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27) (prog-if 00 [VGA])
Subsystem: Fujitsu Siemens Computer GmbH Unknown device 1073
Flags: bus master, stepping, medium devsel, latency 64, IRQ 11
Memory at fa000000 (32-bit, non-prefetchable) [size=16M]
I/O ports at d000 [size=256]
Memory at fbffd000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at 50000000 [disabled] [size=128K]
Capabilities: [5c] Power Management version 2
04:04.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5705 Gigabit Ethernet (rev 03)
Subsystem: Fujitsu Siemens Computer GmbH Unknown device 1073
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 22
Memory at fbfa0000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [48] Power Management version 2
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+ Queue=0/3 Enable-
Credo che il problema sia legato al pacchetto "udev" packet problem.
Si puo' fare qualcosa per installare SME su questo benedetto server ????
Help Me Please...
filloweb
-
ciao
raid HW o SW?
in fase di boot di sme da cd, vedi che carica dei driver?
cosa dice fujitsu per questo tipo di s.o.? RHES 4 è supportato?
prova ad installare con il comando (verifica lo switch se è corretto)
boot: sme nolvm
HTH
Ciao
S.
-
Ciao...
Ho provato anche con un singolo disco... Si blocca SEMPRE su questo pacchetto, solo su questo hardware.
Fujitsu-Siemens ha nel supporto anche la RH 4up5 ma i driver che puoi scaricare sono solo per i controller RAID, SCSI e LAN.
Con l'opzione
boot: sme nolvm
fa uguale.
Non so piu' dove sbattere la testa...
E devo farlo anche abbastanza rapidamente adesso.
Altre idee ???
Fillo.
-
Ma è bloccato a livello di tenere premuto il pulsante per spegnerlo? Il caps lock led si accende/spegne premendo il tasto sulla tastiera?
Il bios è l'ultimo?
Alcune opzioni di boot utili, ma in genere efficaci solo in caso di hang durante il probing del bus pci:
pci=nomsi nolapic noapic
pci=nommconf
-
C'e' un altro post piu' vecchio sempre aperto da me, con maggiori info.
http://forums.contribs.org/index.php?topic=37726.0
Comunque si: bloccato da doverlo spegnere elettricamente. NUM LOCK acceso fisso.
filloweb.
-
Ciao a tutti.
Dopo varie peripezie e ore di lavoro, aiuto da parte di SNT sono arrivato in fondo al problema.
Basta andare su sito della Fujitsu-Siemens e fare un bel downgrade al BIOS della macchina alla versione 6...
Con versioni del BIOS piu' recente, i driver megaide e megaraid hanno dei problemi e si inchioda continuamente il server.
Fillo.