Koozali.org: home of the SME Server

Obsolete Releases => SME Server 7.x => Topic started by: akhilmathema on August 13, 2008, 10:51:59 AM

Title: pppoe connection failure on SME 7.3
Post by: akhilmathema on August 13, 2008, 10:51:59 AM

Hi,
I'm trying to establish a pppoe connection on SME 7.3. But it does not seem to get LCP ConfAck at all. It can get a line sync but not any further on pppoe negotiations. Any suggestions?
tail -f /var/log/wan/current
@4000000048a29bdd372ff7c4 Modem hangup
@4000000048a29bdd372fff94 Waiting for 1 child processes...
@4000000048a29bdd3730037c   script /usr/sbin/pppoe -I nas0 -T 120 -U -m 1412 , pid 19730
@4000000048a29be134344bc4 pppoe: Timeout waiting for PADO packets
@4000000048a29be134610ccc Script /usr/sbin/pppoe -I nas0 -T 120 -U -m 1412  finished (pid 19730), status = 0x1
@4000000048a29be137f1b56c using channel 201
@4000000048a29be1381a155c Using interface ppp0
@4000000048a29be1381d323c Connect: ppp0 <--> /dev/pts/0
@4000000048a29be2382eb2b4 sent [LCP ConfReq id=0x1 <mru 1492> <magic 0x94f982a8>]
@4000000048a29be538352324 sent [LCP ConfReq id=0x1 <mru 1492> <magic 0x94f982a8>]
@4000000048a29be8383d7024 sent [LCP ConfReq id=0x1 <mru 1492> <magic 0x94f982a8>]

Kernel version: 2.6.9-67.0.7.EL
#dmesg|grep pulsar {I'm using internal ADSL card}
pulsar: PCI ADSL ATM Driver V4.0.22 Lib V4.0.11 loaded
pulsar: dev_found = 0, dev_number = 0
pulsar0: Dev:0xf7e48000 IRQ:185 Address:0xF1000000 Length:65536
pulsar0: Registered as ATM device 0 (pulsar0)
pulsar: PCI ADSL ATM Driver V4.0.22 Lib V4.0.11 unloaded
pulsar: PCI ADSL ATM Driver V4.0.22 Lib V4.0.11 loaded
pulsar: dev_found = 0, dev_number = 0
pulsar0: Dev:0xf7e48000 IRQ:185 Address:0xF1000000 Length:65536
pulsar0: Registered as ATM device 0 (pulsar0)
pulsar0: Open for vpi 8 and vci 35
pulsar0: Link Up, Speed = 7616/384
pulsar0: SNR Margin = 13.5dB, Line Atten = 26.5dB
pulsar0: Tx DMA timeout
pulsar0: last_start = 3f8000 last_end = 3f8068
pulsar0: Link Down

#rpm -qa|grep ppp
kmod-ppp-1.0.2-2.2.6.9_67.0.7.EL
warning: only V3 signatures can be verified, skipping V4 signature
rp-pppoe-3.5-22.2.RHEL4.1
ppp-2.4.4-1.3.el4.sme
kmod-ppp-smp-1.0.2-2.2.6.9_67.0.7.EL

Title: Re: pppoe connection failure on SME 7.3
Post by: zatnikatel on August 13, 2008, 03:03:18 PM

how did you setup up your ADSL modem full bridge mode or half bridge

Title: Re: pppoe connection failure on SME 7.3
Post by: akhilmathema on August 14, 2008, 02:51:50 AM

Its an Internal Pulsar card configured on separate interface nas0 instead of eth1

Title: Re: pppoe connection failure on SME 7.3
Post by: CharlieBrady on August 14, 2008, 04:37:43 AM

Quote from: akhilmathema on August 14, 2008, 02:51:50 AM

Its an Internal Pulsar card configured on separate interface nas0 instead of eth1

SME server software has no support for that device.