Koozali.org: home of the SME Server

Legacy Forums => General Discussion (Legacy) => Topic started by: Claudia Siegner on January 16, 2003, 08:47:39 PM

Title: hylafax:Failure to receive silence
Post by: Claudia Siegner on January 16, 2003, 08:47:39 PM

Hello!

I have hylafax installed on my SME-Server Version 5.5.
I can send faxes, but when somebody sends me faxes I receive an email with the following content:

An attempt to receive facsimile on ttyS0 failed because:

    Failure to receive silence.

    ---- Transcript of session follows ----

Jan 16 17:25:49.66: [ 1613]: SESSION BEGIN 00000009 441889576753
Jan 16 17:25:49.66: [ 1613]: HylaFAX (tm) Version 4.1.5
Jan 16 17:25:49.66: [ 1613]: <-- [4:ATA\r]
Jan 16 17:25:52.80: [ 1613]: --> [7:CONNECT]
Jan 16 17:25:52.80: [ 1613]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS0'
Jan 16 17:25:52.80: [ 1613]: RECV FAX: begin
Jan 16 17:25:54.44: [ 1613]: --> [7:CONNECT]
Jan 16 17:25:54.93: [ 1613]: --> [2:OK]
Jan 16 17:25:54.93: [ 1613]: <-- [9:AT+FRH=3\r]
Jan 16 17:25:55.11: [ 1613]: --> [7:CONNECT]
Jan 16 17:25:56.77: [ 1613]: --> [2:OK]
Jan 16 17:25:56.77: [ 1613]: REMOTE TSI "+49 6227 7 0"
Jan 16 17:25:56.77: [ 1613]: <-- [9:AT+FRH=3\r]
Jan 16 17:25:56.81: [ 1613]: --> [7:CONNECT]
Jan 16 17:25:57.01: [ 1613]: --> [2:OK]
Jan 16 17:25:57.01: [ 1613]: REMOTE wants 14400 bit/s
Jan 16 17:25:57.01: [ 1613]: REMOTE wants page width 1728 pixels in 215 mm
Jan 16 17:25:57.01: [ 1613]: REMOTE wants A4 page length (297 mm)
Jan 16 17:25:57.01: [ 1613]: REMOTE wants 7.7 line/mm
Jan 16 17:25:57.01: [ 1613]: REMOTE wants 2-D MR
Jan 16 17:25:57.01: [ 1613]: RECV training at v.17 14400 bit/s
Jan 16 17:25:57.01: [ 1613]: <-- [11:AT+FRM=145\r]
Jan 16 17:25:58.76: [ 1613]: --> [7:CONNECT]
Jan 16 17:26:00.32: [ 1613]: RECV: TCF 2784 bytes, 2% non-zero, 2699 zero-run
Jan 16 17:26:00.33: [ 1613]: --> [10:NO CARRIER]
Jan 16 17:26:00.33: [ 1613]: DELAY 75 ms
Jan 16 17:26:00.41: [ 1613]: TRAINING succeeded
Jan 16 17:26:00.41: [ 1613]: <-- [9:AT+FTH=3\r]
Jan 16 17:26:00.61: [ 1613]: --> [7:CONNECT]
Jan 16 17:26:01.89: [ 1613]: --> [2:OK]
Jan 16 17:26:01.89: [ 1613]: <-- [11:AT+FRM=146\r]
Jan 16 17:26:02.51: [ 1613]: --> [7:CONNECT]
Jan 16 17:26:02.51: [ 1613]: RECV: begin page
Jan 16 17:26:07.89: [ 1613]: RECV: 2357 total lines, 0 bad lines, 0 consecutive bad lines
Jan 16 17:26:07.89: [ 1613]: RECV: end page
Jan 16 17:26:07.89: [ 1613]: --> [10:NO CARRIER]
Jan 16 17:26:07.89: [ 1613]: <-- [9:AT+FRH=3\r]
Jan 16 17:26:07.94: [ 1613]: --> [7:CONNECT]
Jan 16 17:26:08.99: [ 1613]: --> [2:OK]
Jan 16 17:26:08.99: [ 1613]: RECV recv MPS (more pages, same document)
Jan 16 17:26:08.99: [ 1613]: <-- [9:AT+FRS=7\r]
Jan 16 17:26:38.99: [ 1613]: MODEM
Jan 16 17:26:38.99: [ 1613]: RECV FAX (00000009): recvq/fax00006.tif from +49 6227 7 0, route to , 0 pages in 0:46
Jan 16 17:26:38.99: [ 1613]: RECV FAX: Failure to receive silence.
Jan 16 17:26:38.99: [ 1613]: <-- [9:AT+FTH=3\r]
Jan 16 17:26:39.00: [ 1613]: --> [2:OK]
Jan 16 17:26:39.00: [ 1613]: RECV FAX (00000009): session with +49 6227 7 0 terminated abnormally: Failure to receive silence.
Jan 16 17:26:39.00: [ 1613]: RECV FAX: bin/faxrcvd "recvq/fax00006.tif" "ttyS0" "00000009" "Failure to receive silence." "" ""

Can somebody help me?
thanks, Claudia.

Title: Re: hylafax:Failure to receive silence
Post by: Jáder Marasca on January 16, 2003, 10:51:21 PM

Claudia,
From http://www.hylafax.org/archive/2002-08/msg00260.html

"
Put
     Class1SwitchingCmd:  ""
in your etc/config. file and restart faxgetty.

Lee.

"

I hope this solve your problem!

Jáder

Title: Re: hylafax:Failure to receive silence
Post by: Claudia Siegner on January 17, 2003, 01:06:34 PM

Jáder, thank you very much.
it works now!
Claudia.

Title: Re: hylafax:Failure to receive silence
Post by: Jáder Marasca on January 17, 2003, 01:17:43 PM

Claudia,
No problem! You´re welcome!

Thanks by reply the new status!