Hi,
I am using above ide raid card when configure using the raid card bios to configure as raid 0 it will boot to LI and hang. No problem when configure using raid 1 as I am using now. I have 2x120gb hdd and using sme 6.0.1.
Below is the dmesg.
zone(0): 4096 pages.
zone(1): 225280 pages.
zone(2): 32752 pages.
Kernel command line: auto BOOT_IMAGE=SMEServer-up ro root=2103 BOOT_FILE=/boot/vmlinuz-2.4.20-18.7 hdd=ide-scsi
ide_setup: hdd=ide-scsi
Initializing CPU#0
Detected 1992.037 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 3971.48 BogoMIPS
Memory: 1027688k/1048512k available (1160k kernel code, 17240k reserved, 983k data, 120k init, 131008k highmem)
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode cache hash table entries: 65536 (order: 7, 524288 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 65536 (order: 6, 262144 bytes)
Page-cache hash table entries: 262144 (order: 8, 1048576 bytes)
CPU: CLK_CTL MSR was 6003d22f. Reprogramming to 2003d22f
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: Common caps: 0383fbff c1c3fbff 00000000 00000000
CPU: AMD Athlon(tm) XP 2400+ stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfb590, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Using IRQ router VIA [1106/0686] at 00:07.0
Applying VIA southbridge workaround.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16)
Starting kswapd
allocated 32 pages and 32 bhs reserved for the highmem bounces
VFS: Disk quotas vdquot_6.5.1
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS0 at 0x03f8 (irq = 4) is a 16550A
ttyS1 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta3-.2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:07.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci00:07.1
ide0: BM-DMA at 0x9000-0x9007, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0x9008-0x900f, BIOS settings: hdc:DMA, hdd:DMA
SiI680: IDE controller at PCI slot 00:09.0
PCI: Found IRQ 5 for device 00:09.0
PCI: Sharing IRQ 5 with 00:0d.0
SiI680: chipset revision 2
SiI680: not 100% native mode: will probe irqs later
SiI680: BASE CLOCK == 100
, BIOS settings: hde:pio, hdf:pio
, BIOS settings: hdg:pio, hdh:pio
hdc: SONY CDU4811, ATAPI CD/DVD-ROM drive
hdd: CR-4804TE, ATAPI CD/DVD-ROM drive
hde: ST3120022A, ATA DISK drive
hdf: ST3120022A, ATA DISK drive
blk: queue c03725c8, I/O limit 4095Mb (mask 0xffffffff)
blk: queue c037270c, I/O limit 4095Mb (mask 0xffffffff)
ide1 at 0x170-0x177,0x376 on irq 15
ide2 at 0xf880d080-0xf880d087,0xf880d08a on irq 5
hde: attached ide-disk driver.
hde: host protected area => 1
hde: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=14593/255/63, UDMA(100)
hdf: attached ide-disk driver.
hdf: host protected area => 1
hdf: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=14593/255/63, UDMA(100)
ide-floppy driver 0.99.newide
Partition check:
hde: hde1 hde2 hde3
hdf:
ide-floppy driver 0.99.newide
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 227k freed
VFS: Mounted root (ext2 filesystem).
SCSI subsystem driver Revision: 1.00
PCI: Found IRQ 10 for device 00:08.0
PCI: Sharing IRQ 10 with 00:0c.0
scsi0 : AdvanSys SCSI 3.3G: PCI Ultra: IO 0x9C00-0x9C0F, IRQ 0xA
Vendor: HP Model: C1533A Rev: A907
Type: Sequential-Access ANSI SCSI revision: 02
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 120k freed
Adding Swap: 265064k swap-space (priority -1)
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 06:56:59 May 29 2003
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 11 for device 00:07.2
IRQ routing conflict for 00:07.2, have irq 9, want irq 11
IRQ routing conflict for 00:07.3, have irq 9, want irq 11
PCI: Sharing IRQ 11 with 00:0d.1
PCI: Sharing IRQ 11 with 00:0a.0
usb-uhci.c: USB UHCI at I/O 0x9400, IRQ 9
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 11 for device 00:07.3
IRQ routing conflict for 00:07.2, have irq 9, want irq 11
IRQ routing conflict for 00:07.3, have irq 9, want irq 11
PCI: Sharing IRQ 11 with 00:0d.1
PCI: Sharing IRQ 11 with 00:0a.0
usb-uhci.c: USB UHCI at I/O 0x9800, IRQ 9
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 5 for device 00:0d.0
PCI: Sharing IRQ 5 with 00:09.0
usb-uhci.c: USB UHCI at I/O 0xc000, IRQ 5
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 11 for device 00:0d.1
IRQ routing conflict for 00:07.2, have irq 9, want irq 11
IRQ routing conflict for 00:07.3, have irq 9, want irq 11
PCI: Sharing IRQ 11 with 00:0a.0
usb-uhci.c: USB UHCI at I/O 0xc400, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 4
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
PCI: Found IRQ 9 for device 00:0d.2
ehci-hcd 00:0d.2: VIA Technologies, Inc. USB 2.0
ehci-hcd 00:0d.2: irq 9, pci mem f88a8000
usb.c: new USB bus registered, assigned bus number 5
PCI: 00:0d.2 PCI cache line size set incorrectly (32 bytes) by BIOS/FW.
PCI: 00:0d.2 PCI cache line size corrected to 64.
ehci-hcd 00:0d.2: USB 2.0 enabled, EHCI 0.95, driver 2003-Jan-22
hub.c: USB hub found
hub.c: 4 ports detected
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide2(33,3), internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide2(33,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
hdc: attached ide-cdrom driver.
hdc: ATAPI 48X CD-ROM drive, 120kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
hdd: attached ide-scsi driver.
scsi1 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: MITSUMI Model: CR-4804TE Rev: 3.0D
Type: CD-ROM ANSI SCSI revision: 02
st: Version 20030406, bufsize 32768, max init. bufs 4, s/g segs 16
Attached scsi tape st0 at scsi0, channel 0, id 3, lun 0
hdc: DMA disabled
hdd: DMA disabled
PCI: Found IRQ 11 for device 00:0a.0
IRQ routing conflict for 00:07.2, have irq 9, want irq 11
IRQ routing conflict for 00:07.3, have irq 9, want irq 11
PCI: Sharing IRQ 11 with 00:0d.1
3c59x: Donald Becker and others.
www.scyld.com/network/vortex.htmlSee Documentation/networking/vortex.txt
00:0a.0: 3Com PCI 3c905B Cyclone 100baseTx at 0xb400. Vers LK1.1.18-ac
00:10:5a:64:a9:f1, IRQ 11
product code 5152 rev 00.12 date 12-05-98
Internal config register is 1800000, transceivers 0xa.
8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface.
MII transceiver found at address 24, status 786d.
Enabling bus-master transmits and whole-frame receives.
00:0a.0: scatter/gather enabled. h/w checksums enabled
divert: allocating divert_blk for eth0
NET4: AppleTalk 0.18a for Linux NET4.0
/dev/vmmon: Module vmmon: registered with major=10 minor=165
/dev/vmmon: Module vmmon: initialized
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport_pc: Via 686A parallel port: io=0x378
/dev/vmnet: open called by PID 2157 (vmnet-bridge)
/dev/vmnet: hub 0 does not exist, allocating memory.
/dev/vmnet: port on hub 0 successfully opened
bridge-eth0: up
bridge-eth0: attached
/dev/vmnet: open called by PID 2165 (vmnet-natd)
/dev/vmnet: hub 8 does not exist, allocating memory.
/dev/vmnet: port on hub 8 successfully opened
eth0: Setting promiscuous mode.
device eth0 entered promiscuous mode
/dev/vmnet: open called by PID 2364 (vmnet-netifup)
/dev/vmnet: port on hub 8 successfully opened
divert: allocating divert_blk for vmnet8
Universal TUN/TAP device driver 1.5 (C)1999-2002 Maxim Krasnyansky
/dev/vmnet: open called by PID 2384 (vmnet-dhcpd)
/dev/vmnet: port on hub 8 successfully opened
Attached scsi CD-ROM sr0 at scsi1, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
st0: Block limits 1 - 16777215 bytes.
[root@apple build]# SiI680:
bash: SiI680:: command not found
[root@apple build]# dmesg > a
[root@apple build]# vi a
[root@apple build]# less a
Linux version 2.4.20-18.7 (bhcompile@bugs.devel.redhat.com) (gcc version 2.96 20
000731 (Red Hat Linux 7.3 2.96-113)) #1 Thu May 29 06:51:53 EDT 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS)
BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
On node 0 totalpages: 262128
zone(0): 4096 pages.
zone(1): 225280 pages.
zone(2): 32752 pages.
Kernel command line: auto BOOT_IMAGE=SMEServer-up ro root=2103 BOOT_FILE=/boot/v
mlinuz-2.4.20-18.7 hdd=ide-scsi
ide_setup: hdd=ide-scsi
Initializing CPU#0
Detected 1992.037 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 3971.48 BogoMIPS
Any suggestion on how should I solve this? Thanks
Cheers
1 Replies
1428 Views