Topic: bristuff-2.6.9-55.0.9-kmdl

[SARK devs]

Just a quick note to let you know that the Bristuff Kernel module rpm is now available for 2.6.9-55.0.9.  It's up on ftp://selintra.co.uk

You can yum localinstall or rpm -Uvh this rpm depending upon your preference.

This will run with the latest 7.2 yum updated kernel.


Kind Regards

S

[jester]

Removed my previous installation compeltely, installed the bristuffed version with sail 2.2.1 and the new kernel module(s) but could not get my card detected. A 'lsmod' showed me no modules where loaded. Issuing a modprobe zaphfc resulted in a kernel panic (uname -r => ).

I'll try to remove the lot and reinstall tomorrow... anything i might have missed?!

[SARK devs]

I'm assuming you installed the bristuff 1.4 version of asterisk as well?  Yes?

you should install...

bristuff-1.4.9-2.i686.rpm
bristuff-2.6.9-55.0.9-kmdl-1.4.4-2.i686.rpm
sail-2.2.1-537.noarch.rpm

here's ours...

Code: [Select]

[root@switch ~]# rpm -qa | grep bristuff
bristuff-2.6.9-55.0.9-kmdl-1.4.4-2
bristuff-1.4.9-2
[root@switch ~]# rpm -q sail
sail-2.2.1-537
I have no idea why it should panic, our reference box is running just fine.   What does uname -r show?
what does ls /lib/modules/`uname -r`/misc show?

Best



S

[ello]

hi
i have removed my previus installation
 i have installed in this order
bristuff-1.4.9-2.i686.rpm
bristuff-2.6.9-55.0.9-kmdl-1.4.4-2.i686.rpm
sail-2.2.1-537.noarch.rpm

[ello]

hi
i have one x100p installed
i have one brihfc installed

i have removed previus installation
i have installed in this order


       bristuff-1.4.9-2.i686.rpm
       bristuff-2.6.9-55.0.9-kmdl-1.4.4-2.i686.rpm
       sail-2.2.1-538.noarch.rpm

i have probed pci card in sail-pbx tag and the hfc card is present
i press commit taste
but not recognize my card

where is my error?

regards

excuse for my english i speek very very little in this language.

[SARK devs]

I think your problem is caused by a small (but significant) timing problem.

Do this...

Code: [Select]

/etc/init.d/sark start
Wait for this to finish.

Now do your PCIcard probe again.

You should now be OK



Kind Regards

S

[ello]

hello
i launch sark start and output is

FATAL module zaphfc not found
waiting for udev
starting asterisk:        [ok]

i have reinstalled all and output not change

[SARK devs]

what does 'uname -r' output?


Kind Regards

S

[ello]

hi

creed that you mean this

zaptel-kmdl-2.6.9-55.0.9.ELsmp-1.4.6-41.el4

bye dario

[SARK devs]

no...

at the linux console, type the command

Code: [Select]

uname -r

what is the output?

S

[ello]

hello

2.6.9-55.0.9.ELsmp

bye

[SARK devs]

bristuff will not run with the smp kernel.

Restart your system with the EL kernel and you should be fine.

Kind Regards

S

[ello]

hi

ok now view only hfc card
for view the x100 card as I must make

thanks

regards dario

[SARK devs]

OK - too difficult to explain here, but your card is a non-standard card.  Read the instructions here

http://www.selintra.com/docs/cgi-bin/view/Main/DocChapter258


Kind Regards

S