Hi,
I trying to using IPSec over PPPOE with static IP.
I cann't connect to th remote location becuse of IP interfaces ppp0 and eth1 are share address. the IP is assigned by the system. how can I resolve it.
ifconfig
eth0 Link encap:Ethernet HWaddr 00:01:A7:01:08:D0
inet addr:10.0.0.1 Bcast:10.0.0.255 Mask:255.255.255.0
EtherTalk Phase 2 addr:65280/196
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:765 errors:0 dropped:0 overruns:0 frame:0
TX packets:935 errors:0 dropped:0 overruns:6 carrier:0
collisions:0
RX bytes:89562 (87.4 Kb) TX bytes:592555 (578.6 Kb)
eth1 Link encap:Ethernet HWaddr 00:D0:09:04:E7:2A
inet addr:xxx.xxx.xxx.xxx Bcast:212.118.137.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2869 errors:31 dropped:0 overruns:0 frame:31
TX packets:4282 errors:0 dropped:0 overruns:0 carrier:0
collisions:0
RX bytes:713010 (696.2 Kb) TX bytes:368850 (360.2 Kb)
ipsec0 Link encap:Point-to-Point Protocol
inet addr:212.118.137.231 Mask:255.255.255.255
UP RUNNING NOARP MTU:16260 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
EtherTalk Phase 2 addr:0/0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:30 errors:0 dropped:0 overruns:0 frame:0
TX packets:30 errors:0 dropped:0 overruns:0 carrier:0
collisions:0
RX bytes:3899 (3.8 Kb) TX bytes:3899 (3.8 Kb)
ppp0 Link encap:Point-to-Point Protocol
inet addr:xxx.xxx.xxx.xxx P-t-P:212.118.133.136 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1
RX packets:2812 errors:0 dropped:0 overruns:0 frame:0
TX packets:4217 errors:0 dropped:0 overruns:0 carrier:0
collisions:0
RX bytes:647638 (632.4 Kb) TX bytes:274086 (267.6 Kb)
/usr/car/messages
un 23 00:31:33 gw ipsec__plutorun: 003 IP interfaces ppp0 and eth1 share
address xxx.xxx.xxx.xxx!
Jun 23 00:31:33 gw ipsec__plutorun: 003 no public interfaces found
Jun 23 00:31:34 gw ipsec__plutorun: 022 "net.local-net.10.0.1.0": we have no
ipsecN interface for either end of this connection
Jun 23 00:31:34 gw ipsec__plutorun: ...could not route conn "net.local-
net.10.0.1.0"
Jun 23 00:31:34 gw ipsec__plutorun: 022 "gate.local-gate.10.0.1.0": we have no
ipsecN interface for either end of this connection
Jun 23 00:31:34 gw ipsec__plutorun: ...could not route conn "gate.local-
gate.10.0.1.0"
Jun 23 00:31:35 gw ipsec__plutorun: 022 "gate.local-net.10.0.1.0": we have no
ipsecN interface for either end of this connection
Jun 23 00:31:35 gw ipsec__plutorun: ...could not route conn "gate.local-
net.10.0.1.0"
Jun 23 00:31:35 gw ipsec__plutorun: 022 "net.local-gate.10.0.1.0": we have no
ipsecN interface for either end of this connection
Jun 23 00:31:35 gw ipsec__plutorun: ...could not route conn "net.local-
gate.10.0.1.0"
Jun 23 00:31:36 gw ipsec__plutorun: 022 "net.local-net.10.0.1.0": we have no
ipsecN interface for either end of this connection
Jun 23 00:31:36 gw ipsec__plutorun: ...could not start conn "net.local-
net.10.0.1.0"
Jun 23 00:31:36 gw ipsec__plutorun: 022 "gate.local-gate.10.0.1.0": we have no
ipsecN interface for either end of this connection
Jun 23 00:31:36 gw ipsec__plutorun: ...could not start conn "gate.local-
gate.10.0.1.0"
Jun 23 00:31:37 gw ipsec__plutorun: 022 "gate.local-net.10.0.1.0": we have no
ipsecN interface for either end of this connection
Jun 23 00:31:37 gw ipsec__plutorun: ...could not start conn "gate.local-
net.10.0.1.0"
Jun 23 00:31:37 gw ipsec__plutorun: 022 "net.local-gate.10.0.1.0": we have no
ipsecN interface for either end of this connection
Jun 23 00:31:37 gw ipsec__plutorun: ...could not start conn "net.local-
gate.10.0.1.0"
0 Replies
734 Views